Kal22378

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 16 total)
1 2
  • Author
    Posts
  • February 1, 2017 at 5:41 am in reply to: Octolively Board #22799
    Kal22378
    Participant

    Ok, thanks Windell

    February 1, 2017 at 12:04 am in reply to: Octolively Board #22797
    Kal22378
    Participant

    Is it necesary to connect J1 through J4? Or can I leave those connections out?

    January 31, 2017 at 5:39 am in reply to: Octolively Board #22796
    Kal22378
    Participant

    Ok….Thank you Lenore.

    January 30, 2017 at 9:19 pm in reply to: Octolively Board #22794
    Kal22378
    Participant

    For the Octolively schematic I mean.
    Thanks

    January 30, 2017 at 9:08 pm in reply to: Octolively Board #22793
    Kal22378
    Participant

    Hey Windell…..I was wondering if a different Atmega microcontroller would work with this code?
    Atmega16?
    Atmega32?

    January 22, 2017 at 9:17 am in reply to: Octolively Board #22791
    Kal22378
    Participant

    How far apart do you recomend that the ir tx and ir rx be spaced apart?

    January 21, 2017 at 6:06 pm in reply to: Octolively Board #22790
    Kal22378
    Participant

    Ok thanks

    January 21, 2017 at 7:18 am in reply to: Octolively Board #22788
    Kal22378
    Participant

    I have another question for you Windell. Can i make one atmega164 control 128 sensors and leds by using a TLC5940 and a 16 to 1 MUX sheild? If so do i need to rewrite a new code also?

    January 17, 2017 at 8:15 pm in reply to: Octolively Board #22787
    Kal22378
    Participant

    Ok, Thanks again Windell.

    January 17, 2017 at 7:55 am in reply to: Octolively Board #22785
    Kal22378
    Participant

    I have one more question about these boards. If I connect multiple boards together and if I press one mode switch will it sync all of the other boards to that mode?

    January 16, 2017 at 6:34 pm in reply to: Octolively Board #22784
    Kal22378
    Participant

    Ok thank you for explaining this to me. I am new at this, but im sure you could tell..!!!!

    January 16, 2017 at 4:43 pm in reply to: Octolively Board #22782
    Kal22378
    Participant

    Ok, so if I write the code onto a new atmega 164 it will be programmed the same way to use the internal oscillator?

    January 2, 2017 at 9:29 pm in reply to: Atmega 164 #22755
    Kal22378
    Participant

    Ok. Do you know what the voltage would be at those pins? Would it be 5v as to what is applied to the microcontroller?, 

    Thanks
    January 2, 2017 at 9:27 pm in reply to: atmega164 pinouts help #22753
    Kal22378
    Participant

    Ok…thanks.

    January 1, 2017 at 6:00 pm in reply to: atmega164 pinouts help #22751
    Kal22378
    Participant

    I have one more Question for you? can I connect one mode switch to multiple ic’s or do the have to be individule?

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 16 total)
1 2